Page 5 of 7
Woodworking Drill Bits
Posted: Wed Oct 19, 2022 11:12 pm
by jrgallagher
The woodworking drill bits used in the mobile table saw work bench and router table look unusual, but seem to perform very well. What manufacturer are they?
Re: Woodworking Drill Bits
Posted: Thu Oct 20, 2022 10:31 am
by Suso
jrgallagher wrote: ↑Wed Oct 19, 2022 11:12 pm
The woodworking drill bits used in the mobile table saw work bench and router table look unusual, but seem to perform very well. What manufacturer are they?
hi mate, check
this out:
Re: Mobile Workbench with Table Saw & Router Table
Posted: Sat Mar 04, 2023 1:16 am
by rodolpho
Hi Paolo! I leave in Brazil and just acquired the project for my home workshop.
In the cutting plans there are 9mm soft plywood pieces... the problem is: we don't have 9mm here... just 10mm.
The pieces are: 39, DR9 and DR7 (x6)
Questions:
1. Can I go ahead and use 10mm?
2. How do I discover where those pieces are used in the project? Just based on the measurements?
Thanks
Rodolpho
Re: Mobile Workbench with Table Saw & Router Table
Posted: Sat Mar 04, 2023 6:05 pm
by Suso
hi rodolpho,
You won't have any problem using 10mm board. DR7 pieces are the bottoms of the drawers. You will simply have to make the recess for the bottoms of the drawers in the parts with reference 12 a little larger.
You can see the location of all the pieces in the PDF called "Reference Number" that you will find following this route:
Mobile Workbench Plans\Mobile Workbench\Cutting List - Fasteners\Cutting List
Re: Mobile Workbench with Table Saw & Router Table
Posted: Mon Mar 06, 2023 8:10 pm
by rodolpho
Thanks!
Re: Mobile Workbench with Table Saw & Router Table
Posted: Sun Apr 02, 2023 7:25 pm
by superfly4
Hi
I have done the frame and now I'm starting with bench tops. I'm about to order Miter channel and T-tracks but I'm a little bit lost about the T-tracks. Wich ones should I order?
Best regards
Lennart
Re: Mobile Workbench with Table Saw & Router Table
Posted: Tue Apr 18, 2023 8:51 pm
by BodieM
Hi Suso!
I embarrassingly got pretty far into this project before realizing my table saw is the dewalt 7485 rather than the larger 10 inch saw. The major problem I’m seeing is that my fence rack and pinion hits the front and back edges of the table because the rip depth is about 6 inches less on my saw.
Do you recommend modifying the table by:
1) knocking the face off and trimming the cabinets by 6 inches;
2) trying to raise the saw and cut grooves into the surfaces of the HPL;
3) installing a custom fence;
4) just upgrading to a 10 inch saw?
Thanks so much for the help. The table is looking amazing otherwise!
Re: Mobile Workbench with Table Saw & Router Table
Posted: Wed Apr 19, 2023 8:03 am
by Suso
hi mate!
I will tell you my tips in order of preference:
1) Buy the other 10 inch saw, DWE 7492QS
2) Installing a custom fence
3) Make the same
modification as this user:
Re: Mobile Workbench with Table Saw & Router Table
Posted: Mon Apr 24, 2023 8:07 am
by freakazoid
BodieM wrote: ↑Tue Apr 18, 2023 8:51 pm
Hi Suso!
I embarrassingly got pretty far into this project before realizing my table saw is the dewalt 7485 rather than the larger 10 inch saw. The major problem I’m seeing is that my fence rack and pinion hits the front and back edges of the table because the rip depth is about 6 inches less on my saw.
Do you recommend modifying the table by:
1) knocking the face off and trimming the cabinets by 6 inches;
2) trying to raise the saw and cut grooves into the surfaces of the HPL;
3) installing a custom fence;
4) just upgrading to a 10 inch saw?
Thanks so much for the help. The table is looking amazing otherwise!
I have the 7485, too.
1) How did you proceed?
2) Is it possible to convert the plan? Do I have to choose the 7485 as option, before buying the plans?
Thanks for any feedback
Re: Mobile Workbench with Table Saw & Router Table
Posted: Fri Aug 18, 2023 7:12 pm
by Muanis
@suso, what is piece 40 used for? the one attached to the back of the workbench. I can't see you using it on any videos.