Photo of my router mecanism finish...works well!
My router table...
-
- Posts: 6
- Joined: Thu Jun 04, 2015 8:59 am
My router table...
Hi,
I would need some infromation about where to get some of the materials:
Threaded inserts, miter gauge bar and track and security power switch.
thanks in advance
I would need some infromation about where to get some of the materials:
Threaded inserts, miter gauge bar and track and security power switch.
thanks in advance
-
- Posts: 2242
- Joined: Thu Oct 22, 2015 4:51 pm
My router table...
wrote:Hi,
I would need some infromation about where to get some of the materials:
Threaded inserts, miter gauge bar and track and security power switch.
thanks in advance
-Hello onofre, threaded inserts in some hardware store, and here...
http://www.leroymerlin.es/fp/14939855/tuercas-de-embutir-m8x15mm
http://www.herrajessanmartin.com/tienda/herrajes-para-muebles/sistemas-de-union/minifix-rafix-y-maxifix/manguito%C2%A0zamac-sw6%C2%A0m612x15
-Bar and track...
http://www.bricor.es/bricor/detalle.action?idProducto=000000000000060602&idCategoria=03003001002
http://www.bricor.es/bricor/detalle.action?idProducto=000000000000060829&idCategoria=03003001002
or prefer T Track perfil...
http://www.orangealuminum.com/t-slot-framing-systems-and-tracks/t-track.html
and Trespa material...
http://hplstore.com/es/8-trespa-6mm
-Power switch
http://www.ebay.es/sch/i.html?_odkw=interruptor+on+off&_osacat=0&_from=R40&_trksid=m570.l1313&_nkw=emergency+on+off&_sacat=0
...and finally, universal 43mm collet router machine...Very good value
http://cnc-plus.de/en/Spindle-Motors---Spare-Parts/Milling-Spindle-Motors/Kress-1050-FME-1-Milling-Spindle-Motor-with-1050W.html
-
- Posts: 2242
- Joined: Thu Oct 22, 2015 4:51 pm
My router table...
Horizontal router ready to work...
-
- Posts: 2
- Joined: Wed Nov 18, 2015 7:19 pm
My router table...
Hi, I've recently found Your inventions :), and I'm impressed. I have a question about bar and u shape track... measures of track and bar don't match. Did You make some treaded holes and put bolts in it to make the bar wider. The bar has 8mm and inside u-shaped track has 13 mm. Correct me if I'm wrong, or maybe I didn't read Your forum with attention :)
-
- Posts: 2242
- Joined: Thu Oct 22, 2015 4:51 pm
My router table...
Hi Patmos,
yes, I made 4mm threaded holes.
About the size of the bar and the u shape track, It will depend on the track you can find. I'll check the plans but the inner measure of one and the outer of the other should be the same. You may need a little bit of oil to make it smooth.
Regards and good luck with the project.
Paoson
yes, I made 4mm threaded holes.
About the size of the bar and the u shape track, It will depend on the track you can find. I'll check the plans but the inner measure of one and the outer of the other should be the same. You may need a little bit of oil to make it smooth.
Regards and good luck with the project.
Paoson